X-ray head

X-ray head

  Replacement

Follow the instructions given above to remove the basic head control card Code 97660514. Detach all the cables connected to the head that may get in the way. Loosen the screw A that secures the head, move it to the rear and lift it as shown in the fi gure.

X-ray Head

To reinstall the head, perform the procedure in reverse order, being careful to lay the cables properly.

Associating the handheld to the x-ray head

If the handheld or head control Code 97660514 is replaced, the handheld needs to be associated to the head as directed below:

Handheld errors

Error code description Solution
E 01 Button released in advance Hold down the button to take the x-ray again until the beep stops.
E 02 Max. shooting time 7s Take the x-ray again. If the problem persists, go near the head and try again.
E 03 CPU internal error Take out the batteries to reset the handheld. Wait a few seconds, put the batteries back in and take the xray. If the problem persists, replace the handheld.
E 04 Software internal error Take out the batteries to reset the handheld. Wait a few seconds, put the batteries back in and take the xray. If the problem persists, replace the handheld.
E 05 ALU internal error Take out the batteries to reset the handheld. Wait a few seconds, put the batteries back in and take the xray. If the problem persists, replace the handheld.
E 06 Status switching too long Take the x-ray again. If the problem persists, go near the head and try again.
E 07 RF fi eld too low ( 16 consecutive messages lost) Take the x-ray again. If the problem persists, go near the head and try again.
E 08 Incorrect fi rmware version Update the fi rmware for the handheld and head control
card.
E 09 Wrong handheld serial number Enter the correct handheld serial number.
Head control card errors Code 97660514
E 10 Button released in advance Hold down the button to take the x-ray again until the
beep stops.
E 11 Cone type error Wait approximately 4/5 before taking another x-ray after removing or putting on the collimator cone.. Hold down the button to take the x-ray again until the beep stops.
E 12 Hardware internal error Reset the x-ray unit by shutting it off with the main switch. Wait a few seconds, turn the x-ray unit back on and take the x-ray again. If the problem persists, replace the basic head control card Code 97660514
E 13 Emission time greater than 4.9s Reset the x-ray unit by shutting it off with the main switch. Wait a few seconds, turn the x-ray unit back on and take the x-ray again. If the problem persists, replace the basic head control card Cod. 97660514
E 14
E 15
E 16
DSP or internal cycle error Reset the x-ray unit by shutting it off with the main switch. Wait a few seconds, turn the x-ray unit back on and take the x-ray again. If the problem persists, replace the basic head control card Code 97660514
E 17 Mains voltage over maximum limit (more than 15%) Make sure the supply voltage corresponds to the rated one (menu P10)
E 18 Mains voltage below minimum limit (more than 15%) Make sure the supply voltage corresponds to the rated one (menu P10)
Control unit card errors Code 97660515
E 30 0x0010 0x0020
0x0030
Tracking error Make sure led indicator DL5 on control unit card Code
97660515 is on. On the contrary replace the card.
E 31 0x0400 No ZigBee fi eld Take the x-ray again. If the problem persists, go near
the head and try again.
E 32 0x2100 CPU error Reset the x-ray unit by shutting it off with the main switch. Wait a few seconds, turn the x-ray unit back on and take the x-ray again. If the problem persists, replace the control unit card Code 97660515
E 33 0x8000
0x8010
0x8020
0x8030
Head power cable disconnected
or pinched
Make sure the head’s power cable is connected on the control unit card Code 97660515. Check electrical continuity of the cable between the control unit card and x-ray head.

 
 
 
Last updated: 8/12/2011
   
   
 
Copyright © 2000 - 2013 KAB Dental Equipment INC., USA.
All Rights Reserved. www.kabdental.com Copying or reproduction in any matter is strictly prohibited.

Website Designed & SEO by : Skynet Technologies India